|
|
Low-Cost Filtration Barriers for Ultrafine Particles Separation
Kejík, Pavel ; Fekete, Roman (referee) ; Lapčík, Ĺubomír (referee) ; Svěrák, Tomáš (advisor)
V mnoha oborech jsou stále využívána anorganická filtrační media založená na materiálech, jejichž výroba využívá primární suroviny. Jejich výroba je tedy energeticky náročná a v důsledku nákladná a neohleduplná k životnímu prostředí. Cílem této práce je ověřit možnost využití alkalicky aktivovaných materiálů na bázi sekundárních surovin, především vysokopecních strusek (BFS) a popílků z uhelných elektráren (FA), pro výrobu porézních médií schopných v budoucnosti nahradit keramické a jiné anorganické filtry. Výzkum je rozvinut skrze experimentální design založený na výpočetním schématu samostatně vyvinutém s pomocí programu MATLAB. Toto schéma počítá vhodná složení směsí na základě poměrů obsahu nejdůležitějších oxidů ve vstupních surovinách. Tak je zajištěno zohlednění proměnlivého složení vstupních surovin a práce je tím hodnotnější, že její výsledky jsou skrze početní nástroj zohledňující základní oxidové složení surovin zobecnitelné. Zároveň byly však pro srovnání a lepší názornost závislostí vlastností na složení navrhnuty a připraveny i série vzorků založené vždy pouze na jedné ze surovin. Z výsledků vyplývá, že pevnost vzorků z těchto směsí (vytvrzených 24 hodin při 70 °C) ve čtyřbodové ohybové zkoušce dle ČSN EN 12390 5 může přesáhnout 7,6 MPa. Dosažením co možná nejvyšší porozity však zákonitě negativně ovlivňuje pevnost materiálu a výsledný materiál tedy dosahuje pevnosti těsně nad hranicí 6,3 MPa. Výsledky obecně dokazují, že nejvíce je pevnost materiálů ovlivněna poměrem SiO2/Al2O3 a množstvím alkalického aktivátoru. Z výsledků vyplývá, že alkalicky aktivované materiály (AAM) na bázi strusky dosahují i více než dvojnásobné pevnosti analogických materiálů na bázi elektrárenského popílku. Velikost pórů materiálů připravených z tříděných surovin s velikostí zrna od desítek po lehce přes sto mikronů se ve většině případů pohybuje v rozmezí desetin ž jednotek mikronů, v případě výsledného materiálu je to pak přibližně 0,2 mikronu. Celková porozita lisovaných těles se pohybuje těsně pod 40 %, což je v tomto případě téměř dvojnásobek ve srovnání s totožnými materiály na bázi netříděných surovin. Výsledky rovněž ukazují, že materiály na bázi strusky vykazují nižší porozitu než ty na bázi popílku, což je patrně způsobeno rozdílnou morfologií částic obou materiálů – částice strusky jsou nepravidelně hranaté a částice popílku kulaté. V průběhu experimentální činnosti byla pozorována tvorba výkvětů u materiálů na bázi elektrárenských popílků. Pomocí Energo-disperzní spektroskopické analýzy (EDS) byly výkvěty identifikovány jako hydroxid sodný procházející karbonatací za účasti vzdušného CO2. Test permeability vyžadoval, kvůli velmi jemné povaze porézní struktury, přípravu asymetrických filtračních přepážek. Tyto přepážky dosáhli propustnosti 138 L/h.m2.bar pro vodu a 1320 L/h.m2.bar pro vzduch.
|
|
|
Utilizazion possibilities of bricks grinding waste in alkali activated systems
Dzurov, Matej ; Kalina, Lukáš (referee) ; Šoukal, František (advisor)
The bachelor’s thesis deals with usage of brick grinding waste, arising from the grinding process of modern bricks, as a constituent of alkali activated binders. The aim of the thesis is to verify the properties of brick grinding waste and to test mechanical properties of mixtures with different proportions of brick grinding waste and ground-granulated blast furnace slag, activated by commonly available hydroxides and combinations of hydroxides and water glasses. Furthermore, the effects of temperature increase on properties of prepared test samples were investigated and formation of carbonate effluent was observed.
|
|
|
Study of alkali-silica reaction in hybrid systems
Bradová, Lada ; Bílek, Vlastimil (referee) ; Kalina, Lukáš (advisor)
This study evaluates question of alkali–silica reaction (ASR) in hybrid system, which was designed in the bachelor's thesis, to meet the requirements of EN 197-1 and classified to the Blastfurnace CEM III/C cements. The durability of this system is a great unknown. For this reason, the same methods (ASTM C1260, ASTM C289 and ASTM C856) were used to observer the ASR effects as the ones used to observer the Portland cement based concrete. Supplementary methods include determination of compressive strengths according to EN 196-2 and scanning electron microscopy to observe the microstructure. Hybrid system results were compared to two different types of cements, CEM I and CEM III/B. From the results of the ASR evaluation assays, it was found that the hybrid system (CEM III/C-HB) and CEM III/B showed the lowest tendency to ASR. The results of the supplementary methods showed that CEM III/C-HB compressive strength increases after 14 days within NaOH by 43 % in comparison to 28 days strength. Based on those results, it is sure that the CEM III/C-HB shows little susceptibility to ASR.
|
|
|
Development of shrinkage reducing admixtures designed for alkali activated materials
Šístková, Pavlína ; Bílek, Vlastimil (referee) ; Kalina, Lukáš (advisor)
This thesis deals with development of shrinkage reducing admixtures designed for alkali activated materials based on blast furnace slag. The main task of this work is to select the most suitable shrinkage reducing admixture based on experiments, in which can be observed minimal shrinkage and at the same time it will not adversely affect the properties of alkali activated blast furnace slag. In the experimental part of the work, test beams containing shrinkage reducing admixtures were prepared, in which the shrinkage and loss of weight were measured. Moreover, the mechanical properties of individual beams, such as tensile strength and compressive strength, were measured. Next, the surface tension of individual shrinkage reducing admixtures was measured in a mixture with pore solution. The hydration process of alkali activated materials under the action of reducing shrinkage admixtures was monitored by calorimetric analysis. The microstructure of the prepared samples was observed by scanning electron microscopy.
|
|
|
Fixation of the lead in alkali activated materials based on different types of ashes
Cába, Vladislav ; Kalina, Lukáš (referee) ; Koplík, Jan (advisor)
The aim of this work was to develop an alkali activated matrix based mainly on fly ash, to determine the ability to fix lead in these matrices, the impact of added lead on mechanical properties and to reveal the way of lead fixation in these matrices. The matrices consisted mainly of fly ash (four from fluidized bed combustion, one pulverized coal combustion) with an admixture of blast furnace slag and sodium silicate as an activator. Lechates were prepared on the basis of the ČSN EN - 12457-4 standard, lead concentrations in them were measured using an atomic emission spectrometer with inductively coupled plasma. The strengths of the samples were measured after 28 days. Images, element maps and element spectra were taken to determine the structure using a scanning electron microscope with an electron dispersion spectrometer, the samples were analyzed on an infrared spectrometer with a Furier transform, X-ray diffraction analysis and electron spectroscopy for chemical analysis were also used. The individual measurements showed that lead is accumulated in the form of hydroxide. The impact of lead doping on strength of the matrix was different for individual samples. Matrices from both types of fly ash released minimal amounts of lead into leachates, so it is possible to use them to fixate lead.
|
|
|
Effect of plasticizers on the behaviour and properties of alkali activated materials
Langová, Markéta ; Koplík, Jan (referee) ; Kalina, Lukáš (advisor)
Alkali activated materials could be suitable alternative to construction materials based on ordinary Portland cement (OPC). Therefore, it is advisable to pursue these binders further on. Aim of this thesis is to clarify the effect of lignosulfonate-based plasticizer and polycarboxylate-based superplasticizer on the behaviour and nature of alkali activated materials. For the purposes of studying the efficiency of plasticizing additives, the change of workability of alkali activated blast furnace slag in dependence on time, effect of additives on mechanical properties as well as, with usage of isothermal calorimetry, their impact on kinetics of solidification and hardening had been observed. The stability of the plasticizing admixtures in a high alkaline environment such as water glass and sodium hydroxide had been studied using infrared spectrometry. As a last step, X-ray photoelectron spectroscopy (XPS) had been used while clarifying the chemical changes in the structure of plasticizing additives after adsorption to blast furnace slag.
|
|
|
Durability of alkali-activated systems
Šafář, Martin ; Šoukal, František (referee) ; Kalina, Lukáš (advisor)
Alkali activated binders have the potential to become an alternative construction material to ordinary portland cement binders. This thesis concentrates on durability testing of alkali activated blast furnace slag and fly ash based concrete. The chosen aspects of durability included sulfate resistance, acid resistance, carbonation, freeze-thaw resistance, frost-salt resistance and porosity. Microstructural changes and formation of new crystalline phases were observed using XRD and SEM-EDX analysis. Potential application of the tested material from the durability point of view was evaluated by comparison with a reference ordinary portland cement based concrete.
|
|
|
Influence of inorganic admixtures on shrinkage reduction of alkali activated materials
Šístková, Pavlína ; Koplík, Jan (referee) ; Kalina, Lukáš (advisor)
This bachelor thesis is focused on the influence of inorganic admixtures on shrinkage reduction of alkali activated materials. In the theoretical part the issue of alkali activated materials is explained in detail focusing on the reduction of their shrinkage. Alkali activated system is constituted by alkali activated blast furnace slag. Firstly, the effect of inorganic dashes is monitored such as low calcium fly ash and finely ground limestone. Furthermore, the influence of inorganic additives for reducing shrinkage has been studied, namely magnesium oxide and calcium oxide. The aim of this work is to determinate the mechanical properties and shrinkage of individual alkali activated mixture and then discuss whether there was a reduction of shrinkage and what the effect of added dashes and inorganic admixtures was.
|
|
|
Leachability of Cu, Ni and Co from alkali-activated matrices
Janíčková, Vlasta ; Kalina, Lukáš (referee) ; Koplík, Jan (advisor)
The work deals with the determination and comparison of leaching of heavy metals from two types of alkali activated systems based on blast furnace slag and high-temperature fly ash. These systems are capable in their structure encapsulate heavy metals, toxic substances or radioactive substances, which can be harmful for the environment. The aim of this work is to prepare a mixture with acceptable mechanical properties. Leachibility from matrix was tested according to ČSN EN 12457–4, followed by analyses Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Structure of matrix was analysed using Scanning electron microscope (SEM).
|
|
|
Setting control of alkali-activated systems
Komosná, Kateřina ; Novotný, Radoslav (referee) ; Kalina, Lukáš (advisor)
This thesis is focused on the possibilities of setting control of alkali-activated systems based on blast furnace slag. The aim of this work is finding the suitable retarder that most extends the time of setting and also preserves the mechanical properties of alkali-activated material. In experimental section were prepared samples of blast furnace slag, water glass, water and additives in various weight addition. Testing samples have undergone of flexural and compressive strength tests. Then the setting time was determined using the Vicat device. The samples were measured calorimetrically because of monitoring the setting process. Finally the mixtures were observed using scanning electron microscope for a closer view on the structure of samples and distribution of setting retarder.
|
guest ::
